Nintendo 3DS Case - Second part

Today I made a better drawing from the sketch I had used for my 3DS case, and here it is, very simple:
  
I used this pattern both for the outside part (in quilting fabric) and for the inside lining, in brown felt. I stitched the felt part first, as the other part needed to have the pockets fixed to it before making it 
I didn't make any pattern for the pockets, as they were made on the spot ... Anyway the front pocket for the AR cards is a rectangle measuring 8 x 11 cms, with one of the shorter edges with a round "cut off " part, as can be seen in  one of yesterday's photos...  I lined with felt the front pocket too, so that cards would be more protected.
The back pocket on the contrary is left without lining, as anyway games are protected by the Velcro-fastened flap (which is made by a double layer of quilting fabric, two 13x7 rectangles sewed together)..The pocket itself is a 4 x 13 cm rectangle, with three holes cut at regular distances, big enough to show a bit of the content (keep in mind that  they must allow to recognize the game card they contain); two additional seams divide the rectangle  in three pockets.
All these measures don't take into consideration a few millimeters  more, used for seams...But the whole is rather soft and padded by the felt, so you don't need to be extremely precise and actually you can reduce some of the sizes if you don't plan to have a space to contain the shoulder belt (which was a sort of pocket made with remains of felt; I didn't even take measures and made it just by trying it on the finished case and stitching it to its edge).
The worst part was sewing the Velcro tape...Which I made when the case was finished, in order to stitch it to all the layers ...But it's very hard to do it by hand, the tape feels like hard plastics and I ruined my fingers for days in the operation (maybe you could consider to use press buttons, although I didn't want to use them as I think one could damage the content by pressing them  too hard...That's why I chose the tape instead, in spite of difficulty)
Attaching the shoulder belt was very easy by comparison! 

I know this is not  really a tutorial, but I didn't take note of what I did, step-by-step ...And very often I did things in the wrong order (realizing too late what I should have done before sewing some parts together! That's what experience is for, I guess...), so I trust people  with even modest sewing skills will be able to do better than me!

Oggi ho fatto un disegno migliore dello schizzo che avevo utilizzato per fare la custodia del 3DS, eccolo qui:

(Vedi foto)

Ho usato questo modello sia per la parte esterna (in tessuto da quilting) che per la fodera interna in panno marrone. Ho cucito la parte in feltro prima, perche' alla parte esterna andavano applicate le tasche prima di chiuderla e cucirla.
Non ho fatto disegni per le tasche, perche' le ho realizzate al momento... Comunque la tasca anteriore per le carte RA e' un rettangolo che misura 8x11 cm, con uno dei lati brevi tagliato a semicerchio (togliendo cioe' circa un semicerchio di stoffa, come si puo' vedere dalle foto di ieri) Ho foderato di panno anche questa tasca, in modo che le carte siano piu' protette.

La tasca posteriore invece non e' foderata, perche' comunque i giochi sono protetti dall' aletta fermata dal Velcro (che e' fatta da uno strato doppio di tessuto di cotone, cioe' due rettangoli 13x7 cm. La tasca stessa e' un rettangolo 13x 4 cm, con tre buchi circolari tagliati a distanza regolare, grandi abbastanza da mostrare il contenuto ( da tener presente che devono permettere di riconoscere l'etichetta sulla scheda di gioco che contengono); due cuciture dividono questa tasca in tre (tre taschine, ciascuna per una scheda di gioco).

Tutte le misure che ho dato non tengono in considerazione i pochi millimetri da aggiungere per le cuciture;  Ma il tutto e' abbastanza morbido e imbottito dall panno, quindi non c'e' bisogno di essere precisi al millimetro e si possono anzi ridurre alcune misure se si prevede di non dedicare uno spazio alla tracolla ripiegabile (che ha un suo scomparto fatto con avanzi di feltro, non ho nemmeno preso le misure e l'ho solo provata sulla custodia finita, cucendola all'orlo.

La parte peggiore e' stata cucire il Velcro...L'ho fatto a custodia finita, per cucirlo a tutti gli strati di tessuto e panno...Ma e' durissimo da fare a mano, il Velcro sembra di plastica dura e mi sono rovinata le mani per giorni (magari si puo' considerare l'alternativa di usare bottoni automatici, anche se io non li ho voluti perche' temo si possa danneggiare il 3DS premendoli troppo forte...E' la ragione che mi ha fatto scegliere il Velcro nonostante la difficolta').
Cucire la tracolla e' stato uno scherzo in confronto!

Capisco che questo non e' un vero tutorial, ma non ho preso nota delle varie operazioni passo per passo...E spesso ho fatto le cose nell'ordine sbagliato (rendendomi conto troppo tardi di cosa avrei dovuto fare prima di cucire insieme certe parti! L'esperienza serve a questo, immagino...), quindi penso che anche chi ha una modesta esperienza di cucito riesca a fare meglio di me!






Comments

Smithy said…
You should offer these and other similar things for sale! Custom orders....
Kristi said…
Thanks for the tutorial! I bought my daughter a Vtech Innotab for Christmas and have looked all over the internet for ideas on a case for her. Yours is by far the best I've seen. I love the way you did your pockets for the games. Do you mind if I use this to make her Innotab case? I usually post what I make to my blog: www.mamaisaverb.blogspot.com - When I finish this project, I will give you credit for the idea and reference your page with a link, if it's okay with you:)
Elena said…
Of course you can Kristi!
I'll be happy if you manage to adapt it to your needs and share it on your blog; thank you for asking anyway, that was very nice of you!